Some of
the buttons on the remote may not support all of the functions of the original
device remote.
POWER
Turns
your device On/Off and also serves as an indicator when the remote is being
programmed
INPUT
Switches
between the sources connected to your TV
PROGRAMMING YOUR REMOTE DIRECT
CODE ENTRY
Before beginning, please
make sure that the device you want to control is powered on and follow these
three simple steps.
NOTE: Press the program to exit at any time.
Press and hold the
program power button until the button lights up red.
The button’s red indicator light remains on.
NOTE: The
Blackweb universal remote comes pre-programmed to operate many Samsung TVs.
Select the device you
want to program from the Device
Categories:
The button’s red
indicator light blinks once and remains on.
Enter the 4-digit code
from the included list for the category and brand of your device.
The button’s red
indicator light shuts off if a valid code was entered.
If the button’s red
indicator light flashes and remains on after entering four digits, that means
an invalid code was entered. In that case, check the list again and re-enter
the code.
NOTE: Test
the remote with the device to make sure all the buttons work as expected. If
some of the buttons/features don’t work, try a different code in the list.
Repeat this process for each device you wish to control.
It’s recommended to
program your remote by using the Direct Code Entry method, however if
with that method you were not able to find a code that is compatible with your
device, you may try the Auto Code Search method below:
Power on the device that
you want to control.
Press and hold the
Program button until the power button lights up red. The button’s red indicator
light remains on.
Select a device from Device
Categories you would like to control. The button’s red indicator light
blinks once and remains on.
NOTE:
Please refer to the list below if you are unsure
about the device category.
• TV: TV, TV/DVD and other TV combinations.
• SAT/CBL: Satellite, Cable, DVR, and other set-top boxes.
• STREAM: Roku, Apple TV, Xbox, and other streaming media players.
• B-RAY/DVD: Blu-ray Players and DVD Players.
• AMP: Sound Bars, Audio Receivers, and other audio devices.
• AUX: VCRs, Digital Frames, and devices not found on the code list.
Point the remote at the
device you wish to control and then press and hold the OK button until
the device turns off. The button’s red indicator light will blink as the codes
are being tested.
When the device turns
off, immediately release the OK button to lock in the code. The button’s
red indicator light will turn off. Test the remote with the device to make sure
all the buttons work as expected.
If some of the buttons/features don’t work, repeat the process or try the Direct
Code Entry method
NOTE:
It may take over 10 minutes to scan through all the
possible codes for your device. If during the Auto Code Search you have either
accidentally or deliberately released the OK button, you may repeat steps 1 through 5 above to resume the code
search where it left off.
After
the Auto Code Search has exhausted all available codes for the selected category,
the remote’s button's red indicator light blinks three times and turns off. If
none of the codes worked with your device, try the Direct Code Entry method.
For easy access to up to
10 of your favorite channels, follow the steps below.
1. Select a device from Device Categories that controls the channels.
The button’s red indicator light will blink once.
2. Press and hold the
program button until the button lights up red.
The button’s red indicator light remains on.
3. Press the FAV button.
The button’s red indicator light blinks once and remains on.
4. Select the button (0
– 9) that you will use for storing your favorite channel. The button’s red
indicator light blinks once and remains on.
5. Enter the channel
number you wish to program as a favorite channel.
6. Press the FAV button,
the button’s red indicator light will turn off and the channel is saved.
NOTE:
To change a stored favorite channel, repeat steps
1-6 above.
To Access Your Favorite
Channels:
1.
Press the FAV button. The button’s red indicator lights up and remains lit.
2. To access the favorite
channel, press the programmed button for that channel (0-9). The button’s red
indicator light blinks, then turns off as the command is sent.
Volume lock
Use this feature to lock
a device to the remote’s volume control. For example, the remote can be in TV
mode while the volume buttons control your sound bar.
Enabling
Volume Lock:
1.
Press and hold the Program button until the button lights up red. The button’s red indicator light remains on.
2. Select a device from Device
Categories that you want to lock to the remote’s volume control. The
button’s red indicator light blinks once and remains on.
3. Press the VOL+ button. The button’s red indicator light blinks once and
remains on.
4. Press the OK button. The button’s red indicator light will blink
twice and turn off.
Disabling Volume Lock:
1.
Press and hold the Program button until the button lights up red. The button’s red indicator light remains on.
2. Press the VOL- button. The button’s red indicator light blinks once
and remains on.
3. Press the OK button. The button’s red indicator light will blink
twice and turn off.
NOTE:
On most newer HDMI-connected devices, the Volume
Lock feature may be unnecessary as this feature is already built-in.
Channel
lock
Use this feature to lock
a device to the remote’s channel control. For example, the remote can be in TV
mode while the channel buttons control your satellite or cable box.
2. Select a device from Device
Categories that you want to lock to the remote’s channel control. The
button’s red indicator light blinks once and remains on.
3. Press the CH+ button. The button’s red indicator light blinks once and
remains on.
4. Press the OK button. The button’s red indicator light will blink
twice and turn oDisabling Channel Lock:
1. Press and hold the Program button until the button lights up red.
The button’s red indicator light remains on.
2. Press the CH- button. The button’s red indicator light blinks once and
remains on.
3. Press the OK button. The button’s red indicator light will blink
twice and turn off.
ff.
NOTE:
On most newer HDMI-connected devices, the Channel
Lock feature
may be unnecessary as this feature is already built-in.
Code
identification
To identify any of your
programmed codes, follow the steps below.
1. Press and hold the Program button until the button lights up red.
The button’s red indicator light remains on.
2. Select a device from Device Categories that you would like the code for.
The button’s red indicator light blinks once and remains on.
3. Press the A button. The button’s red indicator light blinks once and remains
on.
4. Press the “1” button. Count the number of times the button’s red indicator
light flashes. This is the number corresponding to the first digit of the code.
If the button does not flash, the corresponding code number is 0. Repeat the
process by pressing the 2, 3, and 4
buttons for the remaining digits.
5. Press the A button to
exit.
NOTE: Press A
to exit at any time.
Reset
to factory defaults
1. Press and hold the
Program button until the button lights up red.
The button’s red indicator light remains on.
2. Press the [*] button. The button’s red indicator light blinks once and
remains on.
3. Press the OK button. The button’s red indicator light will flash
twice and the remote will revert to factory settings.
Troubleshooting
1) The remote is in the
correct device category mode (TV, SAT/CBL, STREAM, B-RAY/DVD, AMP, AUX); this
tells the remote which device to operate.
2) The batteries are fresh and properly installed.
3) To remove any obstacles between the remote and the device, and that you’re
aiming the remote at the device’s IR sensor.
The remote can’t be programmed to operate my
device.
•
If you’re using the Direct Code Entry method to enter the codes for your brand
and the device is still not functioning properly after trying all the code
options, try the Auto Code Search method.
• To control combo devices like TV/VCRs or TV/DVDs, you must program the
individual corresponding device buttons to control each part of the combo unit.
Some of the buttons of the remote are not supported
or working properly on my device.
•
It's possible the code that you programmed is not fully compatible with your
device. Try selecting the next code from the options available for the category
and brand of your device.
• There may be some buttons from your device's original remote that are not
supported.
• You may have pressed an invalid button for the device category mode the remote
is in.
The remote will not change the channels on my
device.
•
Make sure the remote is in the correct device category mode (TV, SAT/CBL,
STREAM, B-RAY/DVD, AMP, AUX) that controls the channels.
• Try pressing the ENTER button after you enter a channel number (a requirement
with certain models and brands of TV and/or Cable/Satellite boxes).
The remote will not adjust the volume on my device.
•
Make sure the remote is in the correct device category mode (TV, SAT/CBL,
STREAM, B-RAY/DVD, AMP, AUX) that controls the volume.
My device’s menu or app hub does not appear.
•
Menu and app hub access isn’t supported for all brands. You may need to use
your original remote control to access the menu functions and/or app hub for
some devices.
My remote’s light is blinking
•
If while using the remote the indicator light flashes 3 times, this indicates the
batteries need to be replaced.