When the battery is low
(2.0V-2.3V) and needs to be replaced with fresh batteries, the remote control
LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to
turn on equipment. This remote control
is designed to retain programmed memory for 10 years even after batteries are
removed from the remote control.
DIRECT CODE ENTRY MEHOD
1. Turn on the equipment you wish to
program. (TV, VCR, or DVD)
2. Press the [DEVICE] button (TV or VCR) to be
programmed and the [SELECT] button simultaneously for 3 seconds. The device LED
will turn on indicating the unit is ready to be programmed. {The device LED
will stay lit for 20 seconds. The next step must be entered while the LED is
on.}
3. Point the remote control toward the equipment
and enter the three-digit code number assigned to your brand from the code
tables. [Code list is given by the previous post here] # Tip: The equipment will
turn off when the correct three-digit code number has been entered. You can
verify you have selected the correct code by pressing the [MUTE] button, the
equipment should turn on or turn off.
: If there is more than one three-digit number listed for your
brand, try one code number at a time until your equipment turns off.
4. Store the three-digit code number by pressing
the same [DEVICE] button once again. The device LED will blink twice to confirm
that the code has been stored. Note :
Try all the functions on the remote control. If any of the functions do not
work as they should, repeat from Step 2 using the next three-digit code number
from the same brand list. Make sure that the VCR/VOD button is in the VCR
position when using your VCR.
Auto Search Method.
If the three-digit code numbers
assigned to your brand do not turn off your equipment or the code tables do not
list your brand, you can use the Auto Search Method to find the correct
three-digit code number for your equipment by the following steps:
* Turn on the equipment you wish to operate.
** Press the [DEVICE] button (TV or VCR) to be
programmed and the [SELECT] button simultaneously for 3 seconds. The device LED
will turn on.
Tip: The device LED will light on
for 20 seconds. The next step must be entered while LED is on.
*** Point the remote control toward the equipment
and alternately press the [CH+] (or [CH-]) button and the [MUTE] button. If the
right code number is sent, the equipment will turn off. You can verify that you selected the correct
code by pressing the [MUTE] button again. The equipment should either turn on
or turn off.
**** Press the same [DEVICE] button to store the
code. The Device LED will blink twice to confirm that the code has been stored.
To Find the Three Digit Code
Number That was Stored in the Device.
1. Press the [DEVICE] button
(TV or VCR) you wish to verify and the [SELECT ]button simultaneously for 3
seconds. *Tip: The device LED will turn
on for 20 seconds. The next step must be entered while the LED is on.
2. Press the [INFO] button. The device LED will
blink number of times indicating the number of each digit of the code number.
Each digit is separated by a 1 second interval of the LED being turned
off.
Example :One blink, three blinks
and eight blinks with an interval of 1 second of LED being turned off,
indicates the code number 138. Note :Ten
blinks is equal to the number 0.
Programming a second TV to VCR
Mode.
1. Press the [VCR] button to
be programmed and the [SELECT] button simultaneously for 3 seconds.
Tip: The
device LED will turn on for 20 seconds. The next step must be entered while the
LED is on.
2. Press the [TV] device button to pick up the
TV code table.
3. Point the remote control
toward the equipment and enter the three-digit code number assigned to your TV
brand from the code tables.
4. Store the three-digit code
number by pressing the [VCR] button once again.
The device LED will blink twice to confirm that the code has been
stored.
Volume Punch Through
By following the steps below, the
user can program the volume controls (Volume UP, Volume Down and MUTE) from one
device to operate in another device mode.
The default volume control settings on the remote control is TV volume
control. If you wish to store the CABLE volume control in CBL mode, use the following
steps.
1. Press the [CBL] button and the [SELECT]
button simultaneously for 3 seconds. *Tip: The device LED will light on for 20
seconds. The next step must be entered while the LED is on.
2. Press the [VOL +] button.
3. Press the [CBL] button. The device LED will
blink twice to confirm the programming.
To return to original state:
If you wish to restore the TV
volume control in CBL mode, repeat the above steps by pressing [TV] in Step-3.
Programming the System On/Off Button. This is
designed to program the System on/off button so that it can send out up to
three power on/off commands for the devices you programmed into the remote
control.
1. Press the [CBL] button.
2. Press the [SYSTEM] button
and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will
turn on for 20 seconds.
2. Press the [DEVICE] button
you wish to store in the System On/Off button and repeat this until you stored
all the power commands into the System On/Off button.
4. Press the [CH+] button to
save the power commands you stored. The [CBL] button will blink twice to
confirm the saving.