DIRECT TV REMOTE CONTROL _ SETUP PROCEEDINGS

SETUP PROCEEDINGS

1. Locate the DIRECTV Receiver's brand and model number.
2. Locate the 5-digit code for your DIRECTV Receiver.
3. Power on the DIRECTV Receiver.
4. Slide the MODE switch to the DIRECTV position.
5. Press and hold the MUTE and SELECT keys until the green light under the DIRECTV position flashes twice, then release both keys.
6. Using the number keys, enter the 5-digit code. If performed correctly, the green light under the DIRECTV position flashes twice.
7. Aim the remote at your DIRECTV Receiver and press the PWR key once. The DIRECTV Receiver should turnoff; if it does not, repeat steps 3 and 4, trying each code for your brand until you find the correct code.

ON-SCREEN REMOTE SETUP

Once you have successfully set up your DIRECTV Remote to operate your DIRECTV Receiver, you can set it up to control your TV. 

CONTROLLING THE TV

• Turn on the TV.  NOTE: Please read steps 2-5 completely before proceeding.  Highlight or write down the codes and component you wish to set up before moving on to step 2.

•  Locate the 5-digit code for your TV.
• Slide the MODE switch to the TV position.
• Press and hold the MUTE and SELECT keys at the same time until the green light under the TV position flashes twice, then release both keys.
• Using the number keys enter the 5-digit code for your brand of TV. If performed correctly, the green light under TV flashed twice.
• Aim the remote at your TV and press the PWR key once. Your TV should turn off. If it does not turn off, repeat steps 3 and 4, trying each code for your brand until you find the correct code.
•  Slide the MODE switch to the DIRECTV position. Press TV POWER. Your TV should turn on.

SETTING UP THE TV INPUT KEY

Once you have setup the DIRECTV Remote control for your TV, you can activate the TV INPUT key so you can change the “source”—the piece of equipment whose signal is displayed on your TV:

• Slide the MODE switch to the TV position.
• Press and hold the MUTE and SELECT keys until the green light under the TV position flashes twice, then release both keys.
• Using the number keys enter 9-6-0. (The green light under the TV position flashes twice.)  You now can change the input for your TV.

TO DEACTIVATE THE TV INPUT SELECT KEY

If you want to deactivate the TV INPUT key, repeat steps 1 through 3 from the previous section; the green light will blink 4 times. Pressing the TV INPUT key will now do nothing.

CONTROLLING OTHER COMPONENTS

The AV1 and AV2 switch positions can be setup to control a VCR, DVD, STEREO, second DIRECTV Receiver or second TV you can also use the manual method below:

1. Turn on the component you wish to control (e.g. your DVD Player).
2. Locate the 5-digit code for your component.
3. Slide the MODE switch to the AV1 (or AV2) position.
4. Press and hold the MUTE and SELECT keys at the same time until the green light under AV1 (or AV2) flashes twice, then release both keys.
5. Using the NUMBER keys, enter the 5-digit code for the brand of component being set up. If performed correctly, the green light under the selected position flashes twice.
6. Aim the remote at your component and press the PWR key once. The component should turn off; if it does not, repeat steps 3 and 4, trying each code for your brand until you find the correct code.

Repeat steps 1 through 6 to set up a new component under AV2 (or AV1).

SEARCHING FOR TV,AV1 OR AV2 CODES

If you were unable to find the code for your brand of TV or component, you can try a code search. This process may take up to 30 minutes.

• Turn on the TV or component. Insert a tape or disk if applicable.
• Slide the MODE switch to the TV, AV1 or AV2 position, as desired.
• Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys.
• Enter 9-9-1 followed by one of the following four digits:

COMPONENT TYPE COMPONENT ID

Satellite                         0

TV                                  1

VCR/DVD/PVR            2

Stereo                            3

• Press PWR, or other functions (e.g. PLAY for VCR) you want to use.
• Point the remote at the TV or component and press CHAN+. Repeatedly press CHAN+ until the TV or component turns off.
• Use the CHAN- key to step back a code.
• When the TV or component turns off, stop pressing the CHAN+ key. Then, press and release the SELECT key.  NOTE: If the light flashes 3 times before the TV or component responds, you've cycled through all codes and the code you need is not available. You must use the remote that came with your TV or component.

VERIFYING CODES

Once you have set up the DIRECTV Universal Remote Control using the above steps, use the following instructions to find out the 5-digit code to which your component responded:

1. Slide the MODE switch to the appropriate position.
2. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys.
3. Enter 9-9-0. (The green light under the selected switch position flashes twice.)
4. To view the first digit in the code, Press and release then number 1 key. Wait three seconds, and count the number of times the green light flashes. Write this number down in the leftmost TV, AV1 or AV2 code box .
5. Repeat step 4 four more times for the remaining digits; i.e., press number 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the final digit.

CHANGING VOLUME LOCK

Depending on how you set up your remote, the VOL and MUTE may control the volume only on your TV, regardless of the position of the MODE switch. This remote can be set up so that the VOL and MUTE keys work only with the component selected by the MODE switch. To enable this feature, perform the following steps:

•  Press and hold the MUTE and SELECT keys until the green light under the DIRECTV position flashes twice, then release both keys.
• Using the number keys, enter 9-9-3. (The green light will flash twice after the 3.)
• Press and release the VOL+ key. (The green light flashes 4 times.)   Now the VOL and MUTE keys will work  only for the component selected by the MODE switch position.

TO LOCK VOLUME TO AV1, AV2 OR AV3

• Slide the MODE switch to the AV1, AV2 or TV position to lock the volume.
• Press and hold the MUTE and SELECT keys until the green light under the selected switch flashes twice and release both keys.
• Using the number keys, enter 9-9-3. (The green light flashes twice.)
• Press and release the SELECT key. (The green light flashes twice.).  NOTE: DIRECTV boxes don’t have volume control, so the remote will not allow the user to lock volume to the DIRECTV mode.

RESET TO FACTORY SETTINGS

To reset all the functions of the remote control to the factory defaults (the original, out-of-the-box settings), follow these steps:

1. Press and hold the MUTE and SELECT keys at the same time until the green light flashes twice, then release both keys.
2. Using the number keys, enter 9-8-1. (The green light flashes 4 times.)